Lift the release tab on the latch drive bracket 1 for the drive you want to remove, then slide the drive from its drive bay 2. As well as actually reading my post completely and answering all my questions. Press the card straight down into the expansion socket on the system board 2. The slot on the far right should be used when a port cover is installed. Figure 3-5 Removing a Bezel Blank Replacing the Front Bezel. I really appreciate the time you take your cover everything discussed. To reattach the Smart Cover Lock, secure the lock in place with the tamper-proof screws.
Use the key provided to disengage the lock. If you are installing an optical drive, connect the power cable 1 and data cable 2 to the back of the drive. By risky, I mean that you can turn it into a device with the response and value of a brick. Otherwise, keep the existing version as long as possible. To install a drive into the 3. If it ain't broke - don't fix it.
Use the hole in the bracket that best secures the peripheral device cable. To download the necessary driver, select a device from the menu below that you need a driver for and follow the link to download. Must be something to do with windows 10 on this old machine. Table 1-2 Front Panel Components 5. Rotate up the internal drive bay housing to access the memory module sockets on the system board. After searching through the support forum I read that this is any version 8 bios or after. Insert the hooks on the port cover into the slots on the rear of the chassis, then slide the cover to the right to secure it in place 2.
Figure 4-46 Threading the Keyboard and Mouse Cables Screw the lock to the chassis in the thumbscrew hole using the screw provided. To remove a bezel blank: Remove the access panel and front bezel. Figure 3-21 Sliding the Drives into the Drive Cage Connect the power and data cables to the drive as indicated in the following illustrations. You need this driver for that device. To install the port cover: Thread the cables through the bottom hole on the port cover 1 and connect the cables to the rear ports on the computer. Figure 4-38 Installing the Hard Drive Connect the power cable 1 and data cable 2 to the back of the hard drive. Any thoughts and recommendations are welcome.
Figure 2-47 Engaging the Lock When complete, all devices in your workstation will be secured. For some reason I have the issue currently and on only 2. Plug in the computer and turn on power to the computer. Figure B-3 Removing the Security Screws. No affiliation or endorsement is intended or implied. Lift the card straight up to remove it. Figure 4-19 Disconnecting the Power and Data Cables Rotate the drive cage back down to its normal position.
While lifting the release tab, slide the drive from its drive bay 2. Select the F10 Setup menu and hit the enter key. I work for the Army and we have over 12 thousand system. In other words can I go directly to this bios or must I install all bioses before this one in order? I have read about the delayed restart associated with 2. Tighten the thumbscrew to secure the access panel 2. Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive.
Here is their position on the subject. The hard drive is housed in a carrier that can be quickly and easily removed from the drive bay. Refer to Installing Drives on page 37 for an illustration of the extra M3 metric guide screws location. It updates the Intel Management Engine firmware to version 8. However after much reading on this forum it seems some bioses version 8. They would have been developed at least a year ago if that were the case.
Figure 4-26 Rotating the Drive Cage Down Replace the front bezel if removed and access panel. Warnings and Cautions Before performing upgrades be sure to carefully read all of the applicable instructions, cautions, and warnings in this guide. Figure 2-46 Attaching the Lock to the Chassis Installing a Security Lock. Will I need to go back to windows 7 or 8 from the current win10 to install this bios, and then back to win 10? There is a fix, but the fix would prevent users from running Bitlocker encryption. Gently pull the subpanel, with the bezel blanks secured in it, away from the front bezel, then remove the desired bezel blank.
Using the Smart Cover FailSafe Key to Remove the Smart Cover Lock 165. The screw hole is located on the left edge of the chassis next to the top hard drive bay. Figure 3-25 Removing a Hard Drive Remove the four guide screws two on each side from the old drive. Have 7-Zip Extract to: And let it extract the file into its folder name. Open both latches of the memory module socket 1 , and insert the memory module into the socket 2.
Drivers are the property and the responsibility of their respective manufacturers, and may also be available for free directly from manufacturers' websites. Download and save, but do not run sp73099. Figure 5-30 Securing Peripheral Devices Printer Shown Thread the keyboard and mouse cables through the computer chassis lock. In order to facilitate the search for the necessary driver, choose one of the Search methods: either by Device Name by clicking on a particular item, i. Figure 5-16 Removing the Hard Drive Carrier Remove the four guide screws from the sides of the hard drive carrier. Refer to Installing and Removing Drives on page 106 for an illustration of the extra M3 metric guide screws location.